Detonation-fired pipe flame arresters are safety devices used to prevent the flame from flammable gases and flammable liquid vapors from spreading outward. When designing the fire retardant inner part, the regular packing is designed according to the medium of different mixed gases, the composition of the gas, the pressure drop, the aspect ratio, and the number of elbows to design the MESG value and reach a certain flame retarding speed value. Flow Calibration Column is widely used in the flow calibration of metering pump and dosing device, which can accurately calibrate the output flow of metering pump. Major Material: Plexiglass, transparent PVC and stainless steel; Connection methods have internal thread, external thread, flange. Flow Calibration Column UPVC Flow Calibration Column,PVDF Flow Calibration Column,Plastic Flow Calibration Column,Transparent Flow Calibration Column Ningbo Reamac Imp&Exp Co.,Ltd , https://www.rmiplast.com
Detonation-fired pipe flame arrester Model: GZW-1
Detonation-fired pipe flame arresters are safety devices used to prevent the flame from flammable gases and flammable liquid vapors from spreading outward. When designing the fire retardant, it is based on the medium and gas of different mixed gases.
The fractional, pressure drop, aspect ratio, and number of elbows are used to design the MESG value and achieve a certain rate of fire resistance. When the flame enters the flame arrester, it is cut into many small pieces by regular flame arresting elements.
The flame flow, due to the heat transfer effect and the wall effect, the incoming gas is cooled, so that the cooled gas does not reach the ignition temperature, and the combustion cannot be formed without the ignition temperature, and finally the flame flow is extinguished.
Thereby achieving the purpose of fire prevention.
caliber:
DN20-500
pressure:
1.6MPa-6.4Mpa
Operating temperature:
-20°C- +480°C
Body material:
Cast steel, stainless steel " target=_blank> stainless steel A3 304 304L 316 316L
Fire retardant material:
Stainless steel " target=_blank> stainless steel 304 304L 316 316L
Sealing Gasket:
NBR rubber PTFE metal Gasket
Manufacturing Standards
GB5908-86 SY7511-87
Explosion-proof grade:
BS 5501: IIA IIB IIC
Connection method:
Flange connection
Detonation-fired pipeline flame arrester use:
1. Torch system.
2. Oil and gas recovery system.
3. Gas analysis system.
4. Gas purification and communication system.
5. Coal mine gas emission system.
6. Heating the furnace fuel gas on the pipe network.
7. Pipes that transport flammable gases.
Detonation-fired pipe flame arrester size:
specification
size
pressure
grade
Dimensions (mm)
Nd
L
H
D
K
DN15
1.6MPa
125
142
95
65
4*14
DN20
125
142
105
75
4*14
DN25
130
155
115
85
4*14
DN32
150
168
135
100
4*18
DN40
170
180
150
110
4*18
DN50
190
200
165
125
4*18
DN65
205
210
180
145
8*18
DN80
220
220
200
160
8*18
DN100
240
240
220
180
8*18
DN125
280
260
245
210
8*18
DN150
330
285
285
240
8*22
DN200
380
325
340
295
12*22
DN250
450
365
405
335
12*26
DN300
520
400
460
410
12*26
DN350
595
420
520
470
16*26
DN400
645
450
580
525
16*30
DN450
710
480
640
585
20*30
DN500
780
520
715
650
20*33
DN600
895
550
840
770
20*36
The installation and maintenance of the detonation-fired pipeline flame arrester are as follows:
1. Pipeline flame arrester should pay attention to rain, moisture and oil in the process of transportation and storage.
2. The pipe or accessory Flange Gasket connected to the pipe flame arrester shall be annealed and softened aluminum, copper or copper wire.
3. In order to prevent fire, before and after the oxygen pipeline flame arrester with working pressure greater than 0.6MPa, a copper-based alloy (or stainless steel "target=_blank> stainless steel) pipe should be connected, the length is not less than 5 pipe diameter, and not less than 1.5m. ,
It is not allowed to install all fittings.
4. After the pipeline flame arrester is installed on the pipeline, the system strength and leakage test shall be carried out according to the system design rules, and special cleaning shall be carried out.
5. After the pipeline flame arrester is deactivated for a long time, it should be thoroughly cleaned again when it is used again.
Shanghai Nanshi is a professional manufacturer of anti-explosion-fired pipeline flame arresters. The company produces products: breathing valve, flame arrester, fire retardant breathable cap, fireproof vacuum pressure cap, aluminum alloy Ball Valve , aluminum alloy single Flange Ball Valve, unloading oil. Port, double door bottom valve, oil hole and other series of accessories.
You are welcome to visit our website [http://]. If you have any questions, you can call us and we will do our best to provide you with quality service. phone. Http://news.chinawj.com.cn Editor: (Hardware Business Network Information Center) http://news.chinawj.com.cn