If your home is going to renovate or replace windows, when should you ask the designer to come and measure? What are the special considerations for custom doors and windows? Let's take a little test before revealing the secret? See how much you know about doors and windows! 01 When should the designer come to take measurements? When your construction team is ready to enter the site, you must arrange for your door and window designer to come and measure for you. Because the broken bridge aluminum doors and windows are customized products, the designer will place an order to the factory after measuring the precise size, and process and produce according to the drawings required by the owner. 02 Window production cycle The production cycle of broken bridge aluminum doors and windows will be divided into low and peak seasons, so its processing time is different. There are more people decorating in peak seasons, and the demand for natural doors and windows will increase. The factory needs to produce in order according to the order. When it comes to the customization of doors and windows with complex processes, such as paint baking, it needs to be shipped to a special paint factory, and it takes at least 30 days to complete a set of processes. In addition to time, you need to pay attention to the following four points when the designer visits you to measure! Window color When choosing broken aluminum windows, consider the choice of color, especially the exterior color. For example, for the overall aesthetics of some communities, there will be uniform requirements for the color of the windows. At this time, please confirm with the property in advance. The color of the facade of the windows should be the same as that of the community, and the color of the windows in the home can be selected at will. It can be matched according to the decoration style of your home. The designer will carry the national standard color card with him when measuring at the door, and carefully check the color , To meet your needs for various colors. Pattern of windows The layout of the windows is the second detail that needs to be paid attention to. Whether the community will also require the windows to have the same appearance, so as not to make a mistake, and the property does not allow installation, then it is troublesome. Therefore, it is necessary to check where beams and columns need to be added, and strictly follow the requirements of the community property.~ Do you need a square tube Its function is that if your balcony needs a ceiling or a clothes rail, etc., it may affect the opening of the windows. In order not to fight between the two parties, you must communicate with the designer in advance. You can add this when making and installing windows. A square tube avoids the area of ​​the ceiling and drying racks to ensure that the windows open and close normally. Do you need a subframe If your home involves tiling tiles or wrapping around the window, you need to choose to add an attached frame. The window hinge itself will take up 1.5 cm of the window frame. If tiles are attached or the pass is covered, the width of the window frame will be insufficient, which will affect the normal opening of the window. Add a 2.5 cm sub-frame next to the window frame, and the problem of limited window opening is solved. Does the glass need to be punched? Many owners and friends will punch holes in the kitchen hood ducts, kitchen treasures and wall-hung stoves. It is more convenient to punch holes in the glass than from the wall. You only need to tell the designer the size of the aperture, and the manufacturer will reserve a hole for your glass during production. It is not possible to perforate glass holes on site. Most of the aluminum glass for broken bridges is double-layer and triple-layer glass. It is difficult to perforate on-site, which will cause glass leakage and breakage, which will affect the sealing and heat preservation of the windows. The effect becomes worse.
1.Quality pass Germany TUV testing. Tuv testing is third safety certificate company,.more authoritative.
2. This system welding machine use Surface Mount System to install electron component and the main PCB board is single .So this system could make the machine`s quality is very stable. Rise the quality consistency.
.
3.The power tube of the switch use germany infineon only.The PCB board thickness size is 2.7mm.
4.The insert component use Taiwan KSS.
5.The aluminum web wing is more bigger and weighter than normal.
6.Passed EMC certificate and get the EMC certificate. According to IEC 60974-1 standard.
7. Our machine`s input voltage is auto change between 85V-240V.So could work under any voltage. Like japan 110V or America 110V AC. Like European 220V-240V AC. Like Brazilian 110V/220V together AC.
8.CEL. Could weld Cellulose electrode easy.
9. Welcome any customer to make your design. We have advanced exploit troop.
10.PFC (Power Factor Correction is more than 98%. So according to energy conversation ,environmental protection and low-carbon.
11. VRD make no-load output voltage under 24±2V, But when arc strike twinkling could rise working output voltage.So this technique could have more physical protection.
industrial Welding Machine,Pigeon Welding Machine,Family Quality Welding Machine YongKang WALMA Tools CO., LTD. , https://www.walmatools.com
